Skip to content
TR EN ES
Get the demo

Free Cut List Calculator: Cabinet Parts List

Enter the width, height and depth of a single cabinet box; part sizes, quantities, edge banding and an estimated sheet count are calculated right in your browser. No install, no sign-up.

Box dimensions (mm)
Interior and front
Your sheet size (mm)
PartQtySize (length × width, mm)ThicknessEdge banding
Side2720 × 560181 long edge (front)
Top1564 × 560181 long edge (front)
Bottom1564 × 560181 long edge (front)
Shelf1562 × 540181 long edge (front)
Back (thin panel)1716 × 5968—
Door2716 × 29718all 4 edges

What does this calculator work out?

The calculator builds the parts list for a single, classic cabinet box (a base cabinet, wall cabinet or tall cabinet carcass): two sides, top, bottom, shelves, back panel and, depending on the front you pick, doors or drawer fronts. You can add a plinth too. Each row shows the part name, quantity, cut size, thickness and which edges get banded. Underneath you see the total part count, total area (m²), an estimate of the edge banding in meters and how many sheets you need based on area alone.

Change any dimension and the table recalculates instantly. When you're done, use Download CSV to open the list in Excel or in your own panel saw setup, or Print to hand a paper copy to the shop floor. Everything runs in your browser; the dimensions you enter are never sent anywhere.

What assumptions does it use?

Every cabinetmaker who writes cut lists by hand has their own rules; this tool uses a simple, transparent set. If your shop works differently, read the numbers with that in mind:

  • Sides run full height and full depth; the top and bottom sit between the two sides (width minus two panel thicknesses).
  • Shelves are cut 2 mm short of the inside width and 20 mm short of the depth; the front edge is banded.
  • The back is a thin panel cut 2 mm smaller than the box on every side (width and height minus 4 mm).
  • Doors are 4 mm shorter and narrower than the box; double doors leave a 3 mm gap in the middle. Drawer fronts have a 3 mm gap between them.
  • Edge banding: all four edges on doors and drawer fronts, front edge only on carcass parts. The meter count does not include trim waste.
  • Sheet count is simply total area divided by sheet area. Real sheet nesting (laying parts out on the sheet with as little waste as possible) usually needs more sheets because of saw kerf, grain direction and offcuts.

The first dimension in the table (length) runs with the grain. On a woodgrain finish, the grain on doors and sides runs vertically; keep the part in that direction when you lay it out on the sheet.

A hand-made cut list versus the software's cut list

This tool gives you a quick check for one box. A kitchen, though, has dozens of cabinets, corner solutions, boxes notched around columns, different door styles and a countertop. Calculating each cabinet one by one and merging the lists takes time and multiplies the chance of a mistake.

In CabinetWizard that work comes straight out of the design: the moment you draw a cabinet, the automatic cut list is ready, with edge banding and grain direction columns. The same project also gives you the cutting layout, part labels, DXF and NC files; see the CNC cabinet software page for details. We walk through how it works, instead of measuring and typing lists by hand, step by step in the cut list and countertop dimensions article.

Frequently asked questions

Is this cut list calculator free?

Yes. No account, no install and no email required. Open the page and type your dimensions; the math runs in your browser.

Can I export the list to Excel?

Yes. The Download CSV button gives you the list as a semicolon-separated file that Excel and similar spreadsheet programs open directly.

Can I get the cut list for a whole kitchen here?

This tool is for a single box. For the full list of a kitchen or a wardrobe, plus the cutting layout and CNC output, use the CabinetWizard software; you can download the free demo and try it on your own project.

Are the sizes the same as the software's?

No, this tool uses the simple rules listed above. In the software, settings such as joint type, back panel groove, door gaps and handle choice can be set to your shop's standard, and the list is generated with those settings.